ABSTRACT
Viruses and other microorganisms can enter water sources from different routes and cause pollution and irreparable damage. So, cost-effective and efficient systems for providing safe water are necessary. Efficient filtration systems based on antimicrobial materials have received a lot of attention in this regard. A wide range of materials play an important role in the production of efficient water filtration systems. Metal and metal oxide particles with anti-viral and antimicrobial properties comprising Cu, Cu2O, Ag, TiO2, and ZnO play a valuable role in the preparation of water filtration systems. Biopolymers such as cellulose or carbon nanomaterials like graphene or its derivatives have been reported to provide safe water. In this review, we summarize the use of diverse materials in the preparation of efficient filtration-based systems like membranes and paper filters for water treatment. Pathogen-containing water samples were effectively disinfected using the prepared water disinfection systems.Copyright © 2023 The Royal Society of Chemistry.
ABSTRACT
Objective The epidemic of COVID-19 and its variants is endangering human health. Wearing protective masks can effectively reduce the infection risk by resisting the inhalation of the polluted air containing the coronavirus. Electrospun polyamide nanofibers can be used as the core layer of protective masks and have lately received growing attention because of their high filtration performance and robust mechanical properties. However, existing electrospun polyamide nanofiber filters are usually prepared from toxic solvents which could cause severe environmental pollution and endanger workers' health, hence, their practical application should be restricted. Therefore, it is imperative to seek and develop green-solvent-based polyamide nanofiber filters. Method Innovative polyamide nanofiber filters were developed by direct electrospinning technique based on green solvents (Fig. 1). Ethanol as the solvent and water as the nonsolvent were adopted to prepare the green-solvent-based polyamide (GSPA) nanofibers by designing spinning solutions with different ethanol/water mass ratios (i.e., 10: 0, 9: 1, 8: 2, 7: 3, and 6: 4) . During electrospinning process, the working voltage, tip-to-collector distance, and solution extrusion speed were set as 30 kV, 15 cm and 1 mL/h, respectively. The nanofibers prepared with the different ethanol/water ratios were denoted as GSPA - 0, GSPA - 1, GSPA - 2, GSPA-3, and GSPA-4, respectively. Results It was found that water content had a great influence on the morphological structures of polyamide nanofibers (Fig. 2) - After introducing a small amount of water, the obtained GSPA - 1 nanofibers featuring thinner diameter of 332 nm were compared to the GSPA-0 nanofibers (499 nm). The enhanced conductivity (10. 5 μS/cm) of waterborne spinning solutions (Fig. 3) stimulated more charges on spinning jets and led to larger electrostatic force, thus greatly elongating the jets and thinning the fiber diameter. However, with the further increment of water concentrations from 20% to 40%, the obtained fibers exhibited an increased average diameter ranging from 443 to 1 553 nm, which was mainly attributed to the larger viscosity of spinning solutions. Although water cannot dissolve polyamide, homogenous waterborne polyamide/ethanol solutions can still be obtained with different ethanol/water mass ratios within a broad area in the stable region (Fig. 3) - The average pore size of GSPA -1 membranes decreased by 55% compared with that of GSPA-0 membranes, contributing to high filtration efficiency. Moreover, with different concentrations (10%, 20%, 30%) of water, the fluffy structure of GSPA nanofibers were achieved with a high porosity (> 80%), which would offer more passageways to transmit air rapidly. As the water concentration increased, the breaking strength of membranes increased at first and then decreased (Fig. 5), and the GSPA- 1 membranes exhibited the highest breaking strength of 5. 6 MPa, which was believed to be related to the enhanced entanglements and contacts among the adjacent fibers because of the small fiber diameter. The GSPA -1 membranes displayed the highest filtration efficiency (99. 02%) for the most penetration particles (PM0.3) by virtue of the small fiber diameter but suffered from poor permeability with a pressure drop of 158 Pa. Moreover, the GSPA- 1 membranes possessed the highest quality factor of 0. 029 3 Pa, suggesting the optimal filtration performance among different GSPA membranes. A high PM0.3 removal efficiency (>95%) was achieved for GSPA-1 filters under various airflow velocities ranging from 10 to 90 L/min (Fig. 7). Compared with conventional melt-blown fibers, the GSPA nanofibers featured a smaller diameter and higher Knudsen number (Fig. 8), and PM0.3 were captured mainly on the surfaces of green polyamide nanofibers (Fig. 9), demonstrating the higher adsorption ability benefiting from the larger specific surface area. Conclusion A cleaner production of polyamide nanofibers for air filtration was proposed by direct electrospinning based on green and sustaina le binary solvents of water and ethanol. For the first time, the structure including fiber diameter, porosity, and pore size of electrospun polyamide nanofibers were precisely tailored by manipulating water concentration in spinning solutions. The prepared environmentally friendly polyamide nanofiber filters feature the interconnected porous structure with the nanoscale ID building blocks (332 nm), mean pore size (0.7 μm), and porosity (84%), thus achieving efficient PM0.3 capture performance with the filtration efficiency of 99. 02% and pressure drop of 158 Pa, which could be comparable to previous toxic-solvent-processed nanofibers. Moreover, the GSPA nanofibers exhibit robust mechanical properties with an impressive breaking strength (5 . 6 MPa) and elongation (163. 9%), contributing to withstanding the external forces and deformation in the practical assembly and usage of resultant filters. It is envisaged that the green-solvent-based polyamide nanofibers could be used as promising candidates for next-generation air filters, and the proposed waterborne spinning strategy can provide valuable insights for cleaner production of advanced polyamide textiles. © 2023 China Textile Engineering Society. All rights reserved.
ABSTRACT
The global outbreak of COVID-19 results in the surge of disposable sanitary supplies, especially personal protective face masks. However, the charge dissipation of the electret meltblown nonwovens, which predominate in the commercial face mask filters, confines the durability and safety of commercial face masks. Furthermore, most of the face masks are made from nondegradable materials (such as PP) or part of their degradation products are toxic and contaminative to the environment. Herein, a type of face mask with biodegradable and highly effective PLA bi-layer complex fibrous membrane as filter core is reported. The prepared PLA complex membrane possesses a high-filtration efficiency of 99.1% for PM0.3 while providing a favorable pressure drop of 93.2 Pa. With the PLA complex membrane as the filter core, our face mask exhibits comparable or even higher wearability to commercial face masks, which further manifests our designed PLA complex membrane a promising filter media for face masks. © 2023, The Author(s), under exclusive licence to the Korean Fiber Society.
ABSTRACT
Air pollution is one of the major global problems causing around 7 million dead per year. In fact, a connection between infectious disease transmission, including COVID-19, and air pollution has been proved: COVID-19 consequences on human health are found to be more severe in areas characterized by high levels of particulate matter (PM). Therefore, after the COVID-19 pandemic, the production of air filtration devices with high filtration efficiency has gained more and more attention. Herein, a review of the post-COVID-19 pandemic progress in nanofibrous polymeric membranes for air filtration is provided. First, a brief discussion on the different types of filtration mechanism and the key parameters of air filtration is proposed. The materials recently used for the production of nanofibrous filter membranes are presented, distinguishing between non-biodegradable polymeric materials and biodegradable ones. Subsequently, production technique proposed for the fabrication of nanofibrous membranes, i.e., electrospinning and solution blow spinning, are presented aiming to analyze and compare filtration efficiency, pressure drop, reusability and durability of the different polymeric system processed with different techniques. Finally, present challenges and future perspectives of nanofibrous polymeric membranes for air filtration are discussed with a particular emphasis on strategies to produce greener and more performant devices. © 2023 The Authors. Macromolecular Materials and Engineering published by Wiley-VCH GmbH.
ABSTRACT
Particulate air pollution represented by PM2.5 is one of the biggest environmental challenges in the 21st century. Especially in 2020, the global outbreak of COVID-19 has brought new challenges to melt-blown filter materials, such as the attenuation of filtration efficiency with breathing, even no filtration effect for viruses as their smaller diameter, the sharp decline of filter efficiency after oily filtration cycle, and its limit in some explosive occasions. Here, using the diameter difference of polystyrene (PS), polyvinylidene fluoride (PVDF) and nylon 6(PA6) fibers, we report a multistage structure nanofiber membrane (PS/PVDF/PA6&Ag MSNMs) with high efficiency, low resistance and antibacterial effect by constructing gradient pore structure and introducing silver nanoparticles (Ag NPs), overcoming the above defects. The average filtration efficiency of PS/PVDF/PA6&Ag MSNMs for diisooctyl sebacate (DEHS) monodisperse particles from 0.2 μm to 4.9 μm was 99.88%, and the pressure drop was only 128 Pa. After repeated circulation for 100 times, the filtration efficiency and pressure drop remained stable. Above all, the antibacterial nanofiber membrane with high efficiency and low resistance has been preliminarily constructed, the future research will further focus on the performance after circulation. © 2023 Elsevier Ltd
ABSTRACT
Membrane materials might be used for face protection because they can decontaminate the inhaled air from particle pollution and viruses like the SARS-Cov0-2 which damages our respiration system. In this study, plyethersulfone membranes (PES) were synthesized with green solvent at room temperature and its filtration effectiveness was investigated against nano-bacteria (size 0.05 to 0.2 µm) by measuring their Bacterial Filtration Efficiency (BFE) and micro aerosol size (0.3 µm), and Particulate Filtration Efficiency (PFE). The average SARS-CoV-2 diameters are between 50 nm to 160 nm. A series of experiments were performed to accomplish between 0.03 to 0.21 µm PES sponge like diameters so that can be used for SARS-CoV-2 filtration. Results showed that nanofiltration/ultrafiltration could filter 99.9% of bacteria and aerosol from contaminated air the size of the Covid-19 molecule.
ABSTRACT
With the emergence of the COVID-19, masks and protective clothing have been used in huge quantities. A large number of non-degradable materials have severely damaged the ecological environment. Now, people are increasingly pursuing the use of environmentally friendly materials to replace traditional chemical materials. Silk fibroin (SF) and Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) have received increasing attention because of their unique biodegradability and biocompatibility. In this paper, a series of biodegradable SF/PHBV nanofiber membranes with different PHBV content were fabricated by using electrospinning technology. The morphology of the electrospun SF/PHBV composite nanofiber was observed by scanning electron microscopy (SEM). The average diameters of the pure SF, SF/PHBV (4/1), SF/PHBV (3/1), and SF/PHBV (2/1) nanofibers were 55.16 ± 12.38 nm, 75.93 ± 21.83 nm, 69.35 ± 21.55 nm, and 61.40 ± 12.31 nm, respectively. Fourier transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD) were used to explore the microstructure of the electrospun SF/PHBV composite nanofiber. The crystallization ability of the composite nanofiber was greatly improved with the addition of PHBV. The results of thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) indicated that the thermal stability of SF was better than PHBV obviously, so SF could improve the thermal stability of the composite materials within a certain range. The mechanical properties of the electrospun nanofiber membranes were evaluated by using a universal testing machine. In general, the elongation of the composite nanofiber membranes decreased, and the breaking strength increased with the addition of PHBV. The small pore size of the nanofiber membranes ensured that they had good application prospects in the field of filtration and protection. When the spinning time was 1 h, the filtration efficiency of SF/PHBV/PLA composite materials remained above 95%. © 2021 The Textile Institute.
ABSTRACT
The increasing emergence of infectious diseases like COVID-19 has created an urgent need for filtration/purification materials coupled with multifunctional features such as mechanical integrity, excellent airflow/filtration, and antibacterial/antimicrobial properties. Polymer membranes and metal-organic frameworks (MOFs) have demonstrated high effectiveness in air filtration and purification. MOF nanoparticles have been introduced into electrospun polymer nanofibrous membranes through embedding or postsolution growth. However, the derived hybrids are still facing the issue of (1) limited MOF exposure, which leads to low efficacy;and (2) uncontrollable growth, which leads to pore blocking and low breathability. In this work, we customized an electrospray-on-electrospinning in situ process to dynamically integrate MOF nanoparticles into a robust and elastic continuous nanofibrous membrane for advanced properties including high mechanical strength and flexibility, excellent breathability, particle filtration, and good antimicrobial performance. Biodegradable polylactic acid was reinforced by the poly(hydroxybutyrate)-di-poly(DLA-CL)x copolymer (PHBR) and used as an electrospinning matrix, while MOF nanoparticles were simultaneously electrically sprayed onto the nanofibers with easily controllable MOF loading. The MOF nanoparticles were homogeneously deposited onto nanofibers without clogging the pores in the membrane. The collision of PLA and MOF under the wet status during electrospinning and the hydrogen bonding through C═O and N-H bonds strengthen the affinity between PLA nanofibers and MOF nanoparticles. Because of these factors, the MOF-incorporated PLA/PHBR nanofibrous membrane achieved over 95% particle filtration efficiency with enhanced mechanical properties while maintaining high breathability. Meanwhile, it exhibits excellent photocatalytic antibacterial performance, which is necessary to kill microbes. The electrospray-on-electrospinning in situ process provides an efficient and straightforward way to hybridize one-dimensional (1D) or two-dimensional (2D) nanomaterials into a continuous nanofibrous membrane with strong interaction and controllable loading. Upon integrating proper functionalities from the materials, the obtained hybrids are able to achieve multifunctionalities for various applications. © 2023 American Chemical Society.
ABSTRACT
Particulate matter and spread of viruses, including COVID-19 caused by severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), are two of the most serious problems because of their significant threat to human health. Here, we fabricate ultrafine and bimodal structured polyamide-6 nanofiber/nets (PA-6 NFN) membrane via one-step electrospinning/netting. The PA-6 NFN membranes include ultrafine (∼70 nm) nanofibers and two-dimensional (2D) ultrathin (∼20 nm) nanonets. These membranes are optimized by facilely regulating the solution concentration, incomplete phase separation by adding NaCl, and also applying a high voltage of 22 kV. With integrated properties of small pore size, high porosity, high specific surface area of 108.8 m2/g, and robust tensile strength of 13.70 MPa, the resultant PA-6 NFN membranes exhibit high filtration efficiency of 99.11%, low pressure drop of 81 Pa, and higher quality factor compared to the two standard commercial masks which consist of three-ply surgical mask and respirator face mask. It can include bacteria, fungi, and also viruses including SARS-CoV-2 (with a diameter of about 100 nm). Additionally, after 24 h of operation of the filtration process in a simulated living environment, the obtained air filter still displayed a high filtration efficiency and a less variation pressure drop that shows the long-term performance of PA-6 NFN membranes. In addition, the R2 value was 0.99, which indicates that the calculation results are in good agreement with the measured results. The fabrication of PA-6 NFN membrane makes it a promising candidate for PM0.3 governance at applications including face mask, protective clothing, clean room, and engine intake. © The Author(s) 2022.
ABSTRACT
The demand for air filtration products has increased significantly with the aggravation of air pollution and the pandemic of coronavirus disease (COVID-19). It is urgently needed to develop an air filtration membrane that exhibits lasting filtration performance and antibacterial activity. Herein, we report a large-scale blow spinning technique to produce polyvinylidene fluoride (PVDF) nanofiber membranes for highly efficient air mechanical filtration and its antibacterial modification by adding the silver nanoparticles (AgNPs). The PVDF nanofiber membrane with an area density of only 1.0 g/m2 exhibits the highest filtration efficiency of 98.63% for the particle with a size of 0.3 μm. After eliminating static electricity, there is almost no reduction in the filtration efficiency of particulate matter with a size larger than 1 μm and only 4.69% decrease in the particulate matter with a size of 0.5 μm. Hence, the PVDF nanofiber membrane with nanostructures for air filtration works mainly by the means of mechanical filtration. To inhibit the survival or growth of the intercepted bacteria on the membrane, the PVDF/AgNPs nanofiber membrane was fabricated by adding AgNPs to PVDF nanofibers, which exhibits the strongest antibacterial activity of more than 99% and an excellent filtration efficiency similar to that without adding AgNPs. The nanofiber membrane with antibacterial activity is expected to extend the service or storage time or be reused without loss of filtration performance. Additionally, large-scale production of nanofiber filtration membranes has been realized using a multi-needle blow spinning machine. © 2022 American Chemical Society.
ABSTRACT
The emergence of the SARS-CoV-2 pandemic and airborne particulate matter (PM) pollution has led to remarkably high demand for face masks. However, conventional respirators are intended for single use and made from nondegradable materials, causing serious concern for a plastic-waste environmental crisis. Furthermore, these facemasks are weakened in humid conditions and difficult to decontaminate. Herein, a reusable, self-sustaining, highly effective, and humidity-resistant air filtration membrane with excellent particle-removal efficiency is reported, based on highly controllable and stable piezoelectric electrospun poly (l-lactic acid) (PLLA) nanofibers. The PLLA filter possesses a high filtration efficiency (>99% for PM 2.5 and >91% for PM 1.0) while providing a favorable pressure drop (≈91 Pa at normal breathing rate) for human breathing due to the piezoelectric charge naturally activated by respiration through the mask. The filter has a long, stable filtration performance and good humidity resistance, demonstrated by a minimal declination in the filtration performance of the nanofiber membrane after moisture exposure. The PLLA filter is reusable via common sterilization tools (i.e., an ultrasonic cleaning bath, autoclave, or microwave). Moreover, a prototype of a completely biodegradable PLLA nanofiber-based facemask is fabricated and shown to decompose within 5 weeks in an accelerated degradation environment. © 2022 Wiley-VCH GmbH